Borax Flux Glaze Crucibles 5 Pound Box Melting Gold & Silver Casting Jewelry 5lb

Description

BORAX FLUX 5 Pounds
BORAX FLUX FOR MELTING
GOLD - SILVER
GLAZE CERAMIC CRUCIBLES
BoraxTechnical Grade in a
5 Pound box
, borax is 5 Mol
Borax (
Sodium Tetraborate Pentahydrate)
in the Granular form.
Borax has a wide variety of uses, a component of many products. It can be used to glaze ceramic crucibles, as a flux in casting and soldering.
Borax when used in melting of Gold and Silver helps to dissolve Oxides and other impurities and
produce a fluid borate slag that collects on the surface of the molten metal. This slag is periodically removed, by use of a carbon-graphite or clay rod.
*Item packed and sealed in a clear plastic bag and boxed.
JETS Product # 0326-02025
Made by
, 20 Mule Team® US Borax
SHIPPING: VIA USPS MAIL VIA
PRIORITY
Mail
This product is intended for industrial use only, it is a Technical Grade! SDS Sheets are available on request.
Please VISIT
JETS INC.
our
ebay
store, where you can see many more Melting Supplies and Materials, including a wide selection of Crucibles - in different Shapes and Sizes, Ingot Molds, Stirring Rods, Borax, Gloves, Safety Glasses and many more
J
ewelers
E
quipment
T
ools
and
S
upplies
.
JETS Inc.
RBA  5.4LZ 2XRBA10.8
CKSP M P
Tube-Wringer 401 (COLOR: SILVER)
You will love the Tube Ringer! With little effort it will put a beautiful corrugated pattern on metal sheet up to 24 gauge and wire up to 20ga. The 3 rollers will handle sheet stock up to 2.5" wide and leave the metal nice and smooth. Enhance your artistic efforts with this easy to use economical tool. Made in USA.
UPDATE! I have a video that shows an alternate method to what is described below. I will email you the link once you make a purchase. Past purchases are welcome to the video. Send me an email from your registered Paypal email address.
Specifications
Great for thin Aluminum Foil Ribbons used for Ribbon Microphones
Great for creating beautiful patterns on sheet metal and wire
Made in the USA
3 inch rollers that can handle sheet stock up to 2-1/2 inches wide
Puts a corrugated pattern on sheet metal up to 24 gauge
Can be used on wire up to 20 gauge
Tips For Corrugating Ribbons of
1.8 microns to 2.5 microns
Buy some tracing paper. Tracing paper is great because you can see the ribbon through the paper. You might need to double up the tracing paper. Also, tracing paper has low friction so be careful when moving it around. The ribbon can slide out.
Cut small strips of the tracing paper and fold it in half.
Unfold the paper and place the ribbon inside the paper at the fold and make sure it is laying straight.
Fold the paper again so the paper is on both sides of the ribbon. One edge (length not width) of the Ribbon should be at the fold.
Place one end of the paper into the tube wringer.
Try to make sure that the fold in the paper is perpendicular (tangent) to the gears. You want the ribbon to be as symmetrical as possible. If the ribbon is at an angle when you place it in the tube wringer you will get corrugations that are at an angle.
Turn the handle. Done!
International Shipping
This item will ship via USPS Priority Mail for .00.
Returns
Returns are accepted within 14 days of receiving the item.
International Buyers – Please Note:
Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying.